Images are representations only.

SS-1-TJERNLUND COMPLETE POWER VENTER FOR GAS OR OIL

Part Number: SS-1 Brand: Tjernlund Draft & Ventilation

SS-1 TJERNLUND COMPLETE POWER VENTER FOR GAS OR OIL W/UC1 CONTROL

Price
Request a Quote
Stock
1 In Stock
Does not ship to OH, United States
  • Complete Vent System For Oil Or Gas Has 6" Inlet. Flame Ret. Oil Burner 70,000 -220,000 BTU. Std Oil Burner 70-220,000 BTU. Nat Or LP Gas 50-160,000 BTU. Max Equiv. Feet Is 50'
  • Includes UC1 Control
  • Required Opening 8H" x 8-3/8"W" throught the wall
  • The SS1 features a bottom or rear vent connection.
  • The inlet collar accepts any brand or type of 6" diameter
    vent pipe
  • Verify that the total BTU/hr. input of the heating appliance(s) fall within the proper category listed below.
  • Please note the maximum equivalent feet and capacity
    differs between the SS1 and SS1C.
  • To determine equivalent feet, add the total length of straight vent pipe plus 10 feet for each 90 degree elbow and 5 feet for each 45 degree elbow. Vent runs of over 15 linear feet should use an approved, insulated vent connector to
    prevent problems related to sulfur condensation
Features
  • The SideShot 1 is intended for use with natural
    draft oil and gas heating equipment. It automatically vents the flue gases from heating equipment
    to the outdoors. Surrounding combustible surfaces
    and exhaust gases are kept at safe temperatures
    by pulling outdoor air into its casing and mixing it
    with the flue gases during operation. After each
    burner cycle the SS1 will continue to operate for
    an adjustable period to purge the heater and vent
    of residual gases.
  • The SS1 features a 3-way safety system consisting
    of the UC1 Interlock Control, Fan Proving Switch
    and High Limit. These devices monitor the SS1
    performance and will disrupt the burner if a vent
    system malfunction is detected.
  • Complete Vent System For Oil Or Gas Has 6" Inlet. Flame Ret. Oil Burner 70,000 -220,000 BTU. Std Oil Burner 70-220,000 BTU. Nat Or LP Gas 50-160,000 BTU. Max Equiv. Feet Is 50'
  • Includes UC1 Control
  • Required Opening 8H" x 8-3/8"W" throught the wall
  • The SS1 features a bottom or rear vent connection.
  • The inlet collar accepts any brand or type of 6" diameter
    vent pipe
  • Verify that the total BTU/hr. input of the heating appliance(s) fall within the proper category listed below.
  • Please note the maximum equivalent feet and capacity
    differs between the SS1 and SS1C.
  • To determine equivalent feet, add the total length of straight vent pipe plus 10 feet for each 90 degree elbow and 5 feet for each 45 degree elbow. Vent runs of over 15 linear feet should use an approved, insulated vent connector to
    prevent problems related to sulfur condensation
Features
  • The SideShot 1 is intended for use with natural
    draft oil and gas heating equipment. It automatically vents the flue gases from heating equipment
    to the outdoors. Surrounding combustible surfaces
    and exhaust gases are kept at safe temperatures
    by pulling outdoor air into its casing and mixing it
    with the flue gases during operation. After each
    burner cycle the SS1 will continue to operate for
    an adjustable period to purge the heater and vent
    of residual gases.
  • The SS1 features a 3-way safety system consisting
    of the UC1 Interlock Control, Fan Proving Switch
    and High Limit. These devices monitor the SS1
    performance and will disrupt the burner if a vent
    system malfunction is detected.